Hyper Tough 50 gal wheeled tote size
- Length, lid on
- 45 1/2"
- Width across the lid rim
- 21"
- Height with lid
- 19 1/2"
- Capacity
- 50 gal
- Wheels
- At one end: it goes into the rack wheel end first, handle end out
- Sold at
- Walmart
- Colors
- Black, red lid
- Sizes from
- Store and maker listings: measure one of yours before you cut
Walmart lists it at 45.5" × 21" × 19.5" with a snap lid and recessed wheels at one end, likely on the body of Lowe's 50 gal Commander, which has no wheels and is about 3/4" shorter. Slide it in wheel end first and check that the wheels sit inside the lid's footprint: no listing says whether they stick out.
A 3×3 rack for Hyper Tough 50 gal wheeled totes
It holds 9 totes (450 gallons) and stands 71 1/4" wide, 45 1/2" deep and 66 1/2" tall against a wall, with an open top. Change the layout in the configurator above; the numbers on this page are for the 3×3.
- 21 × 2x4 × 8 ft
- 104 × 2-1/2" screws
- 2 angle brackets to fix it to the wall studs
Cut list
| Part | Qty | Stock | Cut to (length × width) | Notes |
|---|---|---|---|---|
| Legs | 8 | 2x4 SPF | 63 1/2" | Vertical posts |
| Rails | 4 | 2x4 SPF | 71 1/4" | Horizontal full-width members (top/bottom x front/back) |
| Runners | 18 | 2x4 SPF | 45 1/2" | Front-to-back tote supports |
| Spacer Blocks | 2 | 2x4 SPF | 17 1/2" | Assembly jig for row spacing (reuse during build) |
Ladder layout
Every leg gets the same marks. Measure down from the top end of the leg to the top edge of each runner:
- Row 1 (top): 3 1/4"
- Row 2: 24 1/4"
- Row 3 (bottom): 45 1/4"
Posts 21 3/4" apart leave 18 3/4" between the two runners of a bay, so the 21" rim rests on 1 1/8" of each. Cut the two spacer blocks to 17 1/2": stood on one runner, a block sets the next one.
Step by step
Buy the lumber and screws
For a 3×3 rack of Hyper Tough 50 gal wheeled totes: 21 2x4s 8 ft long, 104 2-1/2" screws and 2 angle brackets for the wall studs.
Cut every piece
Cut 8 legs at 63 1/2", 4 rails at 71 1/4", 18 runners at 45 1/2" and 2 spacer blocks at 17 1/2", as in the cut list. A stop block on your saw keeps identical parts identical.
Mark the ladder layout
On one leg, mark the top edge of the top runner 3 1/4" down from the top end, then a mark every 21" below it. Square the marks across and copy them onto all 8 legs.
Build the leg pairs
Screw a runner across a front and a back leg on every mark, with two 2-1/2" screws at each end; a spacer block (17 1/2") standing on one runner sets the next. The middle pairs get runners on both faces, the two end pairs on their inside face only.
Join the pairs with the rails
Stand the pairs on the two bottom rails with 21 3/4" between posts, so the runners of each bay are 18 3/4" apart, and screw the two top rails across the top ends of the legs.
Fix it to the wall and load it
Screw two angle brackets from the top back rail into two wall studs, then slide the totes in with their lids on, wheel end first: the 21" rim rests on 1 1/8" of each runner. Heaviest totes at the bottom.
Totes that fit the same rack
No other tote in our list shares the Hyper Tough 50 gal wheeled's 45 1/2" length and 21" rim width, so build this rack for these totes only, or measure the others first.
Other 50 gallon totes are a different size and need their own rack: Commander 50 gal, Brightroom 50 gal, Sterilite 50 gal, Rubbermaid 50 gal.
FAQ
What size is the Hyper Tough 50 gal wheeled tote?
45 1/2" long, 21" wide across the lid rim and 19 1/2" tall with the lid on, from store listings. It holds 50 gallons and is sold at Walmart. Measure one of yours before you cut.
Which way do Hyper Tough 50 gal wheeled totes go into the rack?
Slide each Hyper Tough 50 gal wheeled tote in wheel end first, so the wheels sit at the back of the bay and the handle end faces you. Check that the wheels sit inside the lid's footprint: if they stick out past the lid, measure the tote's length with the wheels and enter it under Other in the configurator, so the rack comes out deep enough.
Will a rack for Hyper Tough 50 gal wheeled totes fit other 50 gallon totes?
No, not the Commander 50 gal, Brightroom 50 gal, Sterilite 50 gal or Rubbermaid 50 gal: they are a different size, so pick them in the configurator for a rack that fits.
How much lumber does a 3×3 rack for Hyper Tough 50 gal wheeled totes take?
21 2x4s 8 ft long, plus 104 2-1/2" screws and 2 angle brackets for the wall studs. It holds 9 totes (450 gallons) and stands 71 1/4" wide, 45 1/2" deep and 66 1/2" tall.
How far apart are the runners for Hyper Tough 50 gal wheeled totes?
Set the posts 21 3/4" apart, so the two runners of a bay are 18 3/4" apart and the 21" rim rests on 1 1/8" of each. Each row sits 21" above the last: the tote's 19 1/2" height plus a 1 1/2" gap to slide it out.
Build it, guided every step
The Fixie iOS app turns this plan into a customized build for your exact space - pick your dimensions, get an auto-generated cut list, order materials in one tap, and follow the steps with 3D previews. Have something else in mind? Describe it or snap a photo and Fixie will design your own build from scratch - your first design is free.
Download Fixie on the App StoreTote rack plans for other totes
All tote rack plans and the 3D configurator